Automations
Workflow Catalog
Browse HPzenAi automation workflow categories for tanks, pumps, valves, irrigation, flow, motors, relays, connectivity, and scenes.
Choose the Right Workflow
- Start with the physical result you need: fill a tank, close a valve, run irrigation, protect a motor, or send an alert.
- Pick the category that matches the equipment involved.
- Confirm every device used by the workflow is already linked and online.
- Use scenes when the action should run manually from a button instead of automatically from a condition.
Workflow Categories
Open any workflow card to see the dedicated setup guide for that automation.
Automation Library
8 categories for common field workflows
10 workflows
Tank & Pump
Automatic tank filling, sump protection, source priority, and pump retry workflows.
Tank Auto-Fill
Start the pump when the tank runs low.
Tank Full Stop
Stop the pump when the tank is full.
Sump to Overhead
Fill the overhead tank only when the sump has water.
Dry Sump Guard
Never let the pump run on an empty sump.
Borewell Recharge Wait
Pause pumping while the borewell recovers.
Tank Low Alert
Get notified before the tank runs dry.
Refill Band Control
Start low, stop high, and avoid frequent pump toggles.
Sump Recovery Cycle
Pause the pump, wait for recovery, then try again.
Dual Source Priority
Use the preferred water source before switching backup.
Pre-Peak Top-Up
Fill before peak hours when storage is not enough.
7 workflows
Tank & Valve
Valve-based tank filling, overflow prevention, gravity transfer, and periodic valve exercise.
Tank Inlet Valve
Open the inlet valve when the tank needs water.
Overflow Shutoff
Close the inlet before the tank overflows.
Gravity Transfer
Move water between tanks without a pump.
Sump Flood Guard
React before the sump floods over.
Timed Inlet Top-Up
Open the tank inlet on a schedule for a fixed time.
Valve Exercise
Move valves periodically so they do not get stuck.
Valve Stuck Alert
Warn when a valve command does not change state.
8 workflows
Irrigation
Scheduled watering, zone sequencing, booster-assisted watering, and irrigation safety checks.
Scheduled Watering
Water on a schedule for a fixed duration.
Zone Sequence
Water zones one after another automatically.
Booster-Assisted Watering
Bring up line pressure before opening zones.
Valve Watchdog
Catch valves left open for too long.
Misting Cycle
Run short misting pulses on a schedule.
Fertigation Timer
Run dosing or fertigation for a controlled time.
Zone Rest Gap
Add soak time between irrigation zones.
Irrigation Window Lock
Allow watering only inside the planned time window.
9 workflows
Leak & Flow
Water protection workflows for leaks, unexpected flow, budget limits, and reverse flow.
Leak Auto-Shutoff
Shut the water off the moment a leak is suspected.
Unexpected Flow
Detect bursts, theft, or a tap left open.
Water Budget
Stay inside a daily or monthly usage limit.
Pressure Guard
Protect the line from high or low pressure.
Dry-Run Guard (Flow)
Stop the pump when it moves no water.
High-Flow Shutoff
Close the valve when flow is far above normal.
Post-Close Flow Check
Detect water movement after a valve is closed.
Reverse Flow Alert
Warn when water moves in the wrong direction.
Slow Leak Watch
Catch small continuous leakage over a longer window.
16 workflows
Motor & Energy
Motor protection, voltage monitoring, energy budgets, runtime limits, and maintenance workflows.
Dry-Run Guard (Current)
Spot dry running from the motor current.
Overload Protection
Cut power before the motor burns out.
Phase Imbalance Trip
Trip 3-phase motors on unbalanced supply.
Voltage Guard
Protect motors from unsafe voltage.
Runtime Limit
Cap how long the motor runs in a day.
Off-Peak Pumping
Pump when power is cheap and the tank needs it.
Load Shedding
Shed non-essential loads at peak demand.
Energy Budget
Watch daily energy and estimated billing.
Power Factor Alert
A maintenance hint before penalties hit.
Motor Activity Notice
Know every time the motor starts or stops.
Dry-Run Retry Cycle
Pause after dry run, wait, then retry within safe limits.
Anti Short-Cycle
Prevent rapid motor restarts that damage the pump.
Motor Cooldown
Force a rest period after long runtime.
Start Failure Alert
Detect when a start command does not actually run the motor.
Phase Loss Trip
Trip immediately if any phase is missing.
Maintenance Runtime
Schedule service based on accumulated motor runtime.
9 workflows
Relay Bank
Relay-channel schedules, interlocks, pulse actions, duty cycles, and alternating loads.
Channel Schedule
Lights, fertigation, mist - on the clock.
Follow the Pump
A relay channel that mirrors the motor.
Channel Interlock
Never let two channels run together.
Staggered Start
Avoid inrush by starting channels in steps.
Sensor-Driven Channel
Any sensor reading can flip a channel.
Pulse Channel
Turn a relay on briefly for dosing, flushing, or signaling.
Relay Auto-Off
Never leave a relay channel on longer than intended.
Duty Cycle Channel
Repeat on/off cycles for fans, misting, or fertigation.
Alternate Channels
Rotate loads between relay channels to balance usage.
9 workflows
Connectivity
Device offline alerts, stale data warnings, command confirmation checks, and safe-state workflows.
Offline Alert
Know when any device drops off the network.
Sensor-Loss Failsafe
Never pump blind when the sensor is gone.
Gateway Watch
Track failover and weak signal early.
Battery Alert
Replace batteries before devices go dark.
Back-Online Notice
Confirmation when devices reconnect.
Stale Data Alert
Warn when a sensor stops updating while still connected.
Command Ack Timeout
Notify when a device does not confirm a command.
Offline Failsafe
Move actuators to a safe state if control is lost.
Repeated Offline Alert
Escalate noisy devices that keep dropping off.
7 workflows
Scenes
One-tap actions for filling, shutdown, irrigation, service work, and normal operation.
Fill Tank Now
One tap: open the inlet, run the pump, stop at full.
Holiday Mode
Lock the water down while you are away.
Emergency Stop
Everything off and closed, immediately.
Start Irrigation Now
One tap to start the configured irrigation channels.
Stop Irrigation Now
Close irrigation valves and stop related relay channels.
Maintenance Mode
Pause automations while service work is in progress.
Resume Normal
Re-enable paused automations and restore normal operation.